Adex Electronics, ISAIX16-D, Rev D
Bill
Of Materials, Page 1 of 1 , Last Updated: 3/25/98
Item | Qty | Reference | Part | Mfg. | ||||
1 | 4 | - | Female nylon standoff, solder side | |||||
2 | 4 | - | Male nylon standoff | |||||
3 | 3 | W1,W2,W3 | Red Jumper (place on item #20) | |||||
4 | 1 | W5.1 to W5.3 | Black Jumper (place on item #19) | |||||
6 | 1 | W4 | Big Red JUMPER (.2 space) | |||||
7 | 3 | T2,T5,T6 | TVS5 | |||||
9 | 2 | T1,T4 | TVS12 | |||||
10 | 1 | C10 | 180PF | |||||
11 | 1 | D1 | LED,red | |||||
12 | 4 | C4,C1,C6,C8 | +15UF,25V | |||||
14 | 13 | Z1,Z2,Z3,Z4,Z5,Z6,Z7,Z8,Z9,Z10,Z11,Z12,R22 | .1UF, SMD (on both side) | |||||
15 | 2 | - | HEADER 31X1 | |||||
17 | 2 | - | HEADER 18X1 | |||||
18 | 1 | W6 | HEADER 8X1, Pin 2 is cut off as key | |||||
20 | 3 | W1,W2,W3 | HEADER 2X1, W/ red jumper | |||||
21 | 3 | - | 4-40 1/4" screw, solder side | |||||
22 | 1 | - | 4-40 nut | |||||
23 | 1 | - | Box of color tubes | |||||
24 | 1 | SW1 | SW SPDT | |||||
25 | 1 | W5 | HEADER 5X2 , Pin 4 is cut off as key | |||||
29 | 2 | C2,C11 | +0.1UF, TANT, SMD | |||||
*29A | 1 | C7 | +0.68UF or +1.0UF, TANT, SMD | |||||
30 | 1 | F5 | FUSE 5A, SMD (on solder side) | |||||
31 | 3 | F-12,F-5,F12 | FUSE 2A, SMD (on solder side) | |||||
33 | 2 | R14,R13 | 33 OHM, SMD | |||||
34 | 3 | R19,R21,R20 | 300 OHM, SMD | |||||
35 | 1 | R24 | 4.7K ohm, SMD | |||||
36 | 2 | R10,R23 | 8.2K, SMD | |||||
*37 | 4 | R8,R2,R5,R6 | 15K, SMD | |||||
38 | 3 | R3,R4,R7 | 430 OHM, SMD | |||||
39 | 1 | R1 | 560 OHM, SMD | |||||
40 | 2 | R15,R16 | 2K OHM, SMD | |||||
41 | 1 | Q3 | HEXDIP-P, IR9020, DIP4 | IR | ||||
42 | 2 | Q2,Q1 | HEXDIP-N, IR020, DIP4 | IR | ||||
43 | 1 | U14 | Reset IC, SO8 | Proprietary | ||||
44 | 1 | U12 | PAL16V8 (IX1_4), DIP20 | Lattice | ||||
45 | 1 | Q4 | TO220AB, SIP3 | Siliconix | ||||
46 | 1 | U13 | Analog Switch | Proprietary | ||||
47 | 11 | U1,U2,U3,U4,U5,U6,U7,U8, U9,U10,U11 | QS3245, SO20 | Quality Semi or Pericom | ||||
61 | 1 | - | ISA Extender connector (Black) | |||||
70 | 1 | - | G35 Mounting Bracket | |||||
71 | 1 | - | ISAIX16-D PCB |
Note:
1. Short pin 1 and 2 of U14, item # 43.
2. Add 300 ohm thru hole resistor, between Connector pin B01 and B05
3.
Add a +1.0uf cap on top of R6 with - polarity toward ground.
4. Add a +1.0uf cap on top of R5 with + polarity toward ground.
5. C3, C5 are not installed.
* parts and procedures are changed
after the initial release of the board.
[Back] [Home] [Sales] [Support] [News] [Product]
(C) Copyright 1998, Adex Electronics,
Inc. 3 Watson, Irvine, CA 92618, USA. (T) 949-597-1772; (F) 949-597-1729
Email: adex@adexelec.com; Website:
http://www.adexelec.com