Adex Electronics, PCIX32-D, Revision: D
Bill
Of Materials, Page 1 of 1, Last Updated: 3/25/98
Item | Qty | Reference | Part | Mfg | ||||
1 | 2 | - | Female nylon standoff | |||||
2 | 2 | - | Male nylon standoff | |||||
3 | 2 | W22,W23 | Red Jumper (place on item #20) | |||||
4 | 1 | W30.1 to W30.3 | Black Jumper (place on item #19) | |||||
5 | 2 | W26,W27 | Thick shorting wire | |||||
6 | 2 | W21,W24 | Big Red Jumper (.2 spaced) | |||||
7 | 2 | T2,T3 | TVS-5V | |||||
8 | 1 | T4 | TVS5-SMG, SMD | |||||
9 | 2 | T1,T5 | TVS-12V | |||||
11 | 1 | D21 | Red Flashing LED | |||||
12 | 4 | C24,C26,C21,C28 | +15UF,25V | |||||
14 | 11 | Z21,Z22,Z23,Z24,Z25,Z26, Z27,Z28,Z29,Z30,C32 | .1UF, SMD1206 (on both side) | |||||
15 | 4 | - | Header 31X1 | |||||
18 | 1 | W29 | Header 8X1, pin 2 is cut off as key | |||||
20 | 2 | W22,W23 | HEADER 2X1 | |||||
21 | 2 | - | 4-40 1/4" screw (for item #45) | |||||
22 | 2 | - | 4-40 nut (for item #45) | |||||
23 | 1 | - | Box of color tubes | |||||
24 | 1 | SW1 | SW SPDT | |||||
25 | 1 | W30 | Header 5X2, pin 4 is cut off as key | |||||
29 | 1 | +0.1uf, SMD1206 | ||||||
29A | 2 | C22,C27 | +0.68uf or +1.0uf, SMD1206, solder side | |||||
30 | 2 | F5,F3 | 5 Amp Fuse (SMD, on Solder Side) | |||||
31 | 2 | F12, F-12 | 2 Amp Fuse (SMD, on Solder Side) | |||||
33 | 3 | R33,R34,R42 | 33 ohm, SMD | |||||
34 | 4 | R39,R41,R40,R32 | 300 ohm, SMD | |||||
35 | 1 | R43 | 4.7K ohm, SMD | |||||
36 | 2 | R30, R29 | 8.2K ohm, SMD | |||||
37 | 2 | R22,R28 | 15K ohm, SMD | |||||
38 | 4 | R21,R23,R24,R27 | 430- 560 ohm, SMD | |||||
39 | 2 | R25,R26 | 22K ohm, SMD | |||||
39A | 1 | R? | 51 ohm, (0805 size) | |||||
40 | 2 | R35,R36 | 2K, ohm, SMD | |||||
41 | 1 | Q23 | HEXDIP-P (9020), DIP4 | IR | ||||
42 | 1 | Q22 | HEXDIP-N (020), DIP4 | IR | ||||
43 | 1 | Q26 | RESET IC, SO8 | Proprietary | ||||
44 | 1 | U30 | PAL16V8-15 (IX1_4), DIP20 | Lattice | ||||
45 | 2 | Q21,Q24 | TO220AB | |||||
46 | 1 | U31 | Analog Switch | Proprietary | ||||
47 | 9 | U21,U22,U23, U24,U25,U26,U27,U28,U29 | QS3245, SO20 (on both side) | Quality Semi or Pericom | ||||
48 | 1 | - | PCI 32 bit Extender Connector (White) | |||||
49 | 1 | - | PCI Mounting Bracket | |||||
50 | 1 | - | PCIX32-D PCB |
Note:
1. T5 overlaps R22.
2. Cut pad on top of U27.3,
bridge it with a 51 ohm SMD(0805).
3. Remove C31 and R41 if IXPCTR module is installed.
4. Install 240 ohm at R38 and Green SMD LED at R37, if LED is needed.
5. Add a +1.0uf cap on top of R26 with - polarity toward ground.
6. Add a +1.0uf cap on top of R25 with + polarity toward ground.
* parts and procedures are changed after the initial release of the board.
[Back] [Home] [Sales] [Support] [News] [Product] [FAQ]
(C) Copyright 1998, Adex Electronics,
Inc. 3 Watson, Irvine, CA 92618, USA. (T) 949-597-1772; (F) 949-597-1729
Email: adex@adexelec.com; Website:
http://www.adexelec.com