Adex Electronics, PCIX32-E, Revision: E
Bill Of Materials, Page 1 of 1, Last Update: 3/25/98

Item Qty Reference Part Mfg.
1 1 U1 16V8-15 , dip20, IX1_7 Lattice
1A 1 U4 16V8-25, dip20, IX2_2 Lattice
2 3 R2,R1,R5 33
3 4 D2,D4,D5,D6 GREEN LED
3A 1 D1 RED BLINKING LED
4 3 C6,C7,C10 +10UF, 16V, SMD
* 5 13 Z2,Z3,Z4,Z30,C32,Z21,Z29 Z21,Z22,Z23,Z24,Z26,Z27 .1UF
6 2 Q2,Q3 TO220AB Siliconix
* 7 3 R3,R11,R16 8.2K
8 1 U2 ANALOG SWITCH Proprietary
10 1 SW1 SW SPDT
* 11 4 R21,R22,R40,R41 2K
* 11A 1 R32 10K
* 11B 1 R34 12K
* 12 4 R18,R36,R38,R46 15K
* 13 4 R12,R13,R14,R45 4.7K
14 3 R17,R19,R24 300 to 560
* 15 3 C3,CR20,CR23 +.68UF OR +1.0UF
16 1 JP2 JPR3
17 2 C11,C12 +16UF, 25V, THRU HOLE OR SMD
18 3 T1,T2,T5 TVS5, SMG
19 2 T3,T4 TVS12
20 4 R4,R26,R27,R43 240
* 20A 1 R25 220, 1% (2200)
21 3 R28,R37,R39 110 ,5% (110)
21A 1 R15 110 ,1% (1100)
22 1 Q4 SI9400DY or SI9435DY or IR7205 Siliconix or IR (OR IRFD9020 @Q6)
23 1 Q5 SI9955DYor IR7103 Siliconix or IR
24 2 R30,R31 820
25 2 W5,W6 JUMPER
26 1 W7 HEADER 5X2, pin 4 is cut off as key
27 2 W2,W1 4 amp Pluggable Fuse with sockets
27A 2 W3,W4 1.6 amp Pluggable Fuse with sockets
* 28 5 R20,R23,R33,R9,R45 22K
29 1 U15 COMPARATOR Proprietary
31 9 U21,U22,U23,U24,U25,U26,U27,U28,U29 QS3245SO Quality or Pericom
32 4 JP22,JP21,JP23,JP24 HEADER 31
36 1 U6 74HC14SO
37 1 CR1 DIODE,1N4148
38 1 RP1 2K POT, SINGLE TURN
39 1 BZ1 BUZZER
* 40 2 R10,R? 1.5K
41 1 R35 56K
* 42 6 C8,C33,C34,C35,R42,CR34 .01UF
* 43 1 C9 +0.1UF
* 44 1 Z1 +1.0UF
45 1 - PCI 32 Bit Extender Connector (White)
46 1 - PCI Mounting Bracket
47 1 - PCIX32-E PCB

Note:
1. Cut trace to U1.6 and to U1.11 on component/ solder side.
2. Add wire from R34.2 to R40.2 on solder side (Ground).
3. Add wire from U4.3 to via near U4.18, on component side.
4. Add wire from U1.6 to R3.2 via on component side.
5. Add wire from U1.11 to U4.13, on component side.
6. Add R? of item40 (1.5K ohm) between U4.1 and via (VCC) next to it.
7. Do not install R8, R6, U3, R7, C4, C5.
8. Lift U27 pin 3 and add a 51 ohm between pin 3 and pad.
9. CR20(also named C91) in item 15 is mounted on top of R20 with - polarity toward ground.
10. CR23(also named C90) in item 15 is mounted on top of R23 with + polarity toward ground.
11. CR34 in item 42 is mounted on top of R34.
12. Add a wire between via near U29.10 to negative side of C12.
13. The following parts are on the solder side of the board:

R23,C5,R24,C4,U2,C6,C3,T5,T2,T1,C1,C7,C2,U21,U22,U23,U24, U25,Z21,Z22,Z23,Z24,Z30,Z1,R42,R15,R10,R39,R33,R40,R34,CR34.

* parts and procedures are changed after the initial release of the board.


[Back] [Home] [Sales] [Support] [News] [Product] [FAQ]

(C) Copyright 1998, Adex Electronics, Inc. 3 Watson, Irvine, CA 92618, USA. (T) 949-597-1772; (F) 949-597-1729
Email: adex@adexelec.com; Website: http://www.adexelec.com